Skip to content

Signing in and choosing the role

Signing in to Thelgo

To sign in you need three pieces of information, which your company gives you:

Field What to enter
Your company Your company's code in Thelgo. If you open Thelgo from the address dedicated to your company, the field is already filled in and locked (a green tick appears)
Username Your username
Password Your password. The eye-shaped button on the right of the field (Show password / Hide password) shows or hides what you type, so you can check you have not made a mistake

Press Sign in.

Tick Remember me if you want to stay signed in even after closing the browser. Do not use it on a computer shared with others.

If sign-in fails, a red notice appears at the bottom of the page (it disappears by itself after a few seconds), with one of these messages:

  • "Invalid company, username or password.": one of the three details is wrong. For security reasons Thelgo does not say which.
  • "Company not found.": the company code does not exist or is not active.
  • "Too many failed login attempts. Try again after …": after too many wrong attempts, sign-in is blocked for a while. The message gives the time from which you can try again.
  • "Maximum number of concurrently connected operators reached for this account.": your company has a maximum number of operators connected at the same time and it has been reached right now. Try again later or tell the administrator.

The limit on connected users is separate for each role (administrators, operators, agents): the message names the role concerned, for example "Maximum number of administrators connected at the same time reached for this account." or "Maximum number of agents connected at the same time reached for this account.". The limit is checked at sign-in if your user has a single role; if it has more than one, you still get in and the message appears when you choose the role to use.

Cannot get in?

Write to whoever manages your company's account: they can unblock you or reset your password in a minute.

Maintenance in progress

If Thelgo support has put your company's account under maintenance, when you press Sign in a window appears with the title Maintenance in progress and the text "The service is temporarily under maintenance. Please try again in a few minutes.". Close it with Close and try again after a few minutes: it is not an error with your credentials and it does not count as a failed sign-in attempt.

The same window appears if maintenance starts while you already have Thelgo open: the page you are working on stays as it is, but as long as the maintenance lasts, operations do not succeed. Try again after a few minutes.

Forgotten password

  1. On the sign-in screen, press Forgot your password?
  2. Enter Your company and your Username, then press Send instructions.
  3. If the account exists, you receive an email with a link: open it, enter the new password twice and press Reset password.

For security reasons Thelgo always shows the same confirmation message, even if the account does not exist: the window closes and the message appears as a green notice at the bottom. If the link has expired or is not valid, request a new one from the sign-in page.

Session closed by an administrator

An administrator can close your session remotely. In that case you return to the sign-in screen with the message "Your session was closed by an administrator. Sign in again to continue."

Choosing the role

If your user has only one role, you go straight into your area. If it has more than one, Thelgo asks "How would you like to sign in?": click the Operator card. The role choice shows, at the top, the company code and the name of the connected user.

You can change role at any time from the item with the role name at the bottom of the side menu.

One role at a time

With the same user you can work in only one role at a time. If you select another role, for example in another browser tab, the operator session is closed. On the Campaigns page the notice "Your Operator session is no longer active (probably because another role was selected on the same user in the meantime). Press "Retry" to select it again." then appears: press Retry to select the Operator role again.

After signing in as an operator you arrive at the Your campaigns page.

Signing in from the x-bees / Collaboration app

If your company uses the Wildix phone system with the x-bees (or Collaboration) integration, Thelgo opens directly inside the phone system's app and recognizes you from your phone extension, without a username and password.

The first time you open Thelgo from a new computer or device:

  1. "Identity verification required" appears: press Send code by email.
  2. You receive a 6-digit code at the email address registered in Thelgo.
  3. Enter the code and press Verify. If it does not arrive, use "Didn't receive the code? Send it again".

From then on the device is trusted and you will not be asked for the code again, until you disconnect it from your profile (see My profile) or until the administrator revokes it.

If the code cannot be sent

If after pressing Send code by email Thelgo knows that the code will not be sent, you are not left waiting for an email that never arrives: the reason appears in red.

Message What it means and what to do
"No operator is associated with extension N, the one you are trying to sign in with." and below it "Ask your administrator to assign this extension to your operator user in Thelgo." The extension exists on the phone system but is not the fixed extension of any active operator in Thelgo. Ask the administrator to assign it to your user
"No extension N with the email address was found on the PBX. Contact your administrator." The phone system does not know this combination of extension and email. The administrator (or Thelgo support) must check your user's details on the phone system
"The PBX you are signing in from does not match the one linked to this account. Contact your administrator." You are using the app of a phone system different from the company's one in Thelgo
"Sign-in with the iFrame app is not active for this account. Contact your administrator." The integration with the app is not active for your company: Thelgo support is needed
"Unable to contact the PBX to verify the extension. Please try again shortly." Temporary problem: the Try again button appears
"Too many failed attempts: please try again later." Your network address is blocked for a while: Try again appears, but it is better to wait
"We could not send the code to your user's email address. Please try again shortly; if the problem persists, contact your administrator." The email with the code was not sent (missing or wrong address, or email sending not working): Try again appears

Messages without the Try again button require the administrator's intervention: trying again right away is of no use.

Other situations you may come across:

  • "No Thelgo operator recognized for this extension. Contact your administrator.": the app did not tell Thelgo your extension, your email or the phone system. Close and reopen the app; if it persists, contact the administrator.
  • "This page must be opened from inside collaboration/x-bees.": you opened the integration's address directly in the browser.
  • If your company uses x-bees and you have a fixed extension, you must sign in from the app: if you try to sign in from the normal login page, Thelgo may refuse access and offer you the Download the x-bees app button (or the Collaboration one) to install the right program for your operating system.
  • If instead the administrator has left you without an extension, you sign in from the normal login page even if the company uses the app (you cannot, however, use Thelgo's telephony).

Don't have the app yet?

The administrator can email you the links to download the app (Collaboration or x-bees, for Windows and macOS) directly from your user record.

Inside x-bees the Thelgo menu is on the right-hand side and the Log out button is not there: signing out is handled by the x-bees app.